100*20mm 365nm UV LED Curing System for UV Glue Curing

Environmental pollution is small, UV coating VOC content is very low, is recognized green environmental protection product. So we designed 100*20mm 365nm UV LED Curing System specially for it. But UV Curing system not only use on UV coating, also can use in UV printing, UV plastic glazing oil, UV varnish. Normal temperature curing, UV LED Curing Machine is suitable for plastic work-piece, do not produce thermal deformation.



Parameters :
Irradiation Head :
Power : 170W
I / O Voltage : 110V / 220V
Current : 1.8A
Illuminance : 1-6W
Cooling Method : fan cooling
Emitted Area : 100*20mm
Size : 108*82*88mm (L*W*H)
Weight : 1kg





Controller :
Control Method : pedal control
Size : 280*200*230mm (L*W*H)
Weight : 3.5kg
Configuration : pedal*1, connection line*1, power line*1





Advantages :
1.The product has simple operation steps, compact design and convenient installation.
2.High power UV LED, fast curing speed.
3.With timing function, you can set the time.


Application :

200*20mm Large Area LED UV Curing Machine for Coating Curing LED UV Ink UV Glue Curing

UV LED Light Curing System is radiation curing of the coating, because the coating ground has a photoinitiator, and the photoinitiator reacts under the action of uvled light to achieve curing.

Size of Controller

Outside Dimensions	L330*W140*H130mm	Power	50W
Cooling Method	Fan Cooling	Power Input	100-240V AC 50-60HZ
Material / Weight	About 3.5Kg Black Sheet Metal	LED Head Number	One, Independently controlled
RS232 串口通信 RS232 Serial Communication	可查询和调节强度、时间、模式 Can query and adjust intensity, time and mode	Display and Operation	Touch screen, time, intensity, mode adjustable
LED Cumulative Time	Record accumulated using time	Control Method	Connected with MCU, PLC and other automatic equipment to control and feedback the work state

Size of Emitted Head

Emitted Area	200*20mm	Power	<350W
Outside Dimension	L130*W130*H130mm	Recommended Height	5mm
Cooling Method	an Cooling	Wavelength	365	385	395	405
Material / Weight	Sheet Metal / About 3.3Kg	Luminous Power (mW/cm2)	2200mW	2500mW by EIT
		LED Life	20000 H
Monitoring Methods	Temperature	Connection Cable	2/5m （Customizable）

Irradiation Head of 200*20mm Large Area LED UV Curing Machine

UVLED surface light source curing products, if you need to cure the following products, it is recommended to use our UVLED surface light source


At present, uvled radiation-cured products have penetrated into all aspects of industrial production and daily life, and are almost ubiquitous. Here are just a few typical examples.
(1) Coated discs, optical fibers, magnetic tapes, magnetic cards, high-end goods bags, photographic film, magazine covers, vacuum metal plastics, cans, furniture veneers, laminates, wall panels, vinyl tiles and tiles, galvanized metal pipes and Leather decoration, etc.
(2) uvled ink lithographic offset printing, letterpress printing, flexographic printing, gravure printing and screen printing;
(3) uvled adhesive automotive headlights, pressure sensitive labels and transfer printing, electronic device packaging and cladding, medical plastic parts assembly, etc.;
(4) Electronic device printed circuit board conformal coating, resist, solder resist, character ink, anti-dry film, protective coating, etc.;
(5) Other printing plates, medical devices, dental fillings, cosmetic boxes, ophthalmic lenses, golf balls, trophies, snowboards, snowmobiles, advertising signs and other coating curing or decoration, and three-dimensional optical casting processing.


The main application areas of UV LED surface light source curing:
Wood coating - wood primer and surface varnish and paint: filler (filling the interior and surface voids of the board); water-based furniture coating.
Plastic coatings - thin film coatings and hard coatings: automotive parts, instruments, optical discs, credit cards, window films, and metallized plastic low-profile coatings for automotive headlights and lighting components.
Paper coating - surface glazing, metallized paper substrate coating for decorative paper, labels, cards and paper.
Floor coating - vinyl carpet, vinyl silicon, parquet flooring.
Metal coatings - food cans, automotive and instrument decoration, traffic tunnel wall panels.
Silicon germanium coating (paper/film) - release liner, label, casting.
Electronic coatings - conformal coatings, encapsulating compounds, photoresists, soft (hard) disks, optical disks, video tapes, magnetic tapes, optical fibers.
Inks - lithography (cardboard boxes, flexible packaging, magazines, publications), screen printing (plastic labels, plastic bottles, foils, paper and cardboard packaging) and printing.
Adhesives - laminates (paper or film / wood, film, paper, foil, etc.), general bonding (automotive parts, optics), and pressure sensitive adhesives (labels, contact papers/films, etc.).
Crosslinking - heat shrinkable film, electrical insulation material.

Light Blocking UV LED Debonding Machine Semiconductor UV Film Degumming Curing Box

UV LED Debonding Machine Lighting Blocking UV LED Curing Oven Semiconductor UV Film Degumming Curing Box
UV  debonding machine optical lens, LED, IC, semiconductor, integrated circuit board, mobile hard disk and other semiconductor materials UV film degumming use

Paramerters :

Type	DSX-UV350L	Outside Dimension	453*553*500mm
Power	2400W	Emitted Area	350*350mm
Voltage	58V	Irradiation Height	50mm
Current	40A	Curing Speed	1-10s
Service Life	20000 hours	Control	PLC
Cooling Method	Air Cooling	Input Voltage	220V
Control Method	PLC automatic control	Weight	76.5kg
Screen Size	7 inch	Standby Power	90W

UV Dissolver Performance and Features:
The curing speed of the adhesive is generally 30-40 seconds, but depending on the adhesive properties and suitability of the film and the wavelength of the lamp, the curing time will increase or decrease, but this system It is highly applicable. For example, it can be used in R&D and a large variety of production lines for UV film debonding of semiconductor materials such as optical lenses, LEDs, ICs, semiconductors, integrated circuit boards, and mobile hard disks.

Introduction :
UV debonding machine is suitable for 6/8/12’’ chip whole chip irradiation use, the theme part is made of stainless steel, aluminum alloy, reliable refrigeration, stable performance, high film precision and stability, simple operation.








What are Features of UV Dissolver Features?
1. Wafer size: up to 6 inch, 8 inch, 12 inch
 2. The operator simply places/unloads the work, and the other work is fully automatic.  
3. So small, the desktop model contains imported cold light source to uniformly produce light with a wavelength of 350-400nm, eliminating the glue of the film.
 4, with low temperature, uniform exposure, compact structure, low energy consumption, is the ideal model for the semiconductor industry

Reading
In the ordinary dispenser manufacturers, such as some dispensing controllers, the domestic imitation technology is very mature, the market competition is very fierce, the price has plummeted, and even a few machines have appeared. However, domestic dispensers generally have low precision and are not stable enough. Some high-tech industries, when it comes to purchasing glue dispensers, can only find world brands.Therefore, in the case of high precision, it is waiting for the people with lofty ideals to make further efforts.When the market is fiercely competitive, only quality and service can make you stand out.  

How to Process the Dispenser?
1. Opening the glue  
when opening the rubber head, because there is a gap between the rubber outlet and the rubber valve, there is no glue between the rubber nozzles. If the rubber outlet is opened, the movement will start immediately. Lead to a short section of lack of glue at the beginning of the track. In order to avoid this situation, after the glue is opened, it is postponed for a while, waiting for the glue to flow out, and then perform the subsequent movement. This delay time is called the glue opening delay. 

2. After the rubber is  
closed, there is still no glue flowing between the rubber outlet and the rubber valve. If it is moved immediately after closing the rubber head, it may constitute a glue tailing phenomenon. In order to avoid the attack, after the rubber head is closed, the glue is allowed to flow for a while, and then the follow-up action is performed.This delay is called the glue delay. 

3. The height of the drawing is high  
because the viscosity of some glues is large, and the gap is slowly raised at a constant speed to break the glue, which does not affect the glue track. This interval is called the drawing height. 

4. Lifting Height  
When the track is finished, after moving to the starting point of the next track, in order to avoid the impact of the rubber head, lift the rubber head up to a height at the finished point to ensure that the rubber head is safe to hit the needle, and then move to the next section. The starting point of the track, this height is called the lifting height. 

5. Early closing of the glue  
to close the glue, that is, the early closing of the glue interval means that in the continuous track coating, the plastic head is closed before reaching the end point, and the residual pressure and the excess glue are used to finish the final section of the track to avoid the pile of glue. i.e., the length of this track "glue off interval." complete action 
After the dispensing of the entire teaching track is completed, in order to facilitate the pick-and-place of the workpiece, increase the processing power or eliminate the processing error, the user can set the glue head to move to the specified orientation, or the starting point of the processing file, or the processing file completion point, or reset, or File connection. This project is called the completion action. 

6. Pulling up and Lifting  
because of the viscosity of the glue, the wire drawing action after the glue is closed can not reach the action of pulling the broken wire, and the shape of the pulled rubber wire may not meet the requirements. Therefore, after closing the rubber head, performing the diagonal pull up action for the wire drawing preparation 

7. Glue Heating 
can try to heat the glue to a suitable temperature, the fluidity of the added glue, and can also handle the drawing in a certain sense! Keep an eye on the temperature of the heating is not too high!

What does Pleasma Cleaner do ?

The vacuum plasma cleaning machine is plasma processing the pen tongue of ABS material.

Efficient plasma cleaning for surface treatment‎

The left pen tongue is treated by vacuum plasma, while the right pen tongue is not treated by plasma. You can see that the plasma-treated pen tongue on the left is already hydrophilic and can absorb water well. The right side of the pen tongue without vacuum plasma cleaning, water quickly dripping, not hydrophilic.

Light Blocking LED UV Curing Oven For UV Glue UV Curing Box For Mobile Phone Screen Repair 395nm

Light Blocking LED UV Curing Oven UV Glue UV Curing Box Mobile Phone Screen Repair 395nm

UVLED curing box for micro-speakers, motors, cameras, lenses, displays, PCBA; medical equipment, research institutes, 3D printing resin curing UV glue curing

As we all know, UVLED curing equipment will emit glare ultraviolet light during the curing process, and the laboratory basically has no way to block light, which causes great pollution to the environment. At this time, the UVLED curing box can protect it well. effect. Guangdong SpaceLight Technology Co., Ltd specializes in the production of UVLED curing box for UVLED curing light source. Its operation is simple, convenient, small in size and powerful in function. It is suitable for laboratory, research and research, colleges and other occasions.

Trustworthy UVLED curing equipment manufacturers

 For many years, Guangdong SpaceLight Technology Co., Ltd has been focusing on the development and production of UVLED curing equipment. The experienced technical team and service team will provide customers with better and more comprehensive services regardless of pre-sales and after-sales.

Parameters : 

Brand	DSX	Input Voltage	220V/110V
Name	Intelligent UV LED Curing Box	Intensity	Touch Screen Adjustable
Material of Light Head	Superconducting hot aluminum	Defensive Function	/
UV LED Chip	Korea LG UV LED Chip	Cooling Method	Air Cooling
Irradiance Area	200*200mm	Control Method	I/O
Irradiance Distance	5-20mm (best effect)	Add Coolant	/
Power of Light	400W	Environment	0-40°C
Wavelength	395nm (can be customized 365nm-420nm)	Quality Guarantee	One year

Advantages : 

1.Energy saving : 80% less than mercury vapor lamps

2.High efficiency : high light intensity, fast curing speed, ink does not stick to the board, good calendering effect.

3.Mercury vapor lamp will produce carbon monoxide harmful gas, and UV LED is a long wave, a single wavelength, will not produce gas, harmless to human body, the working environment is clean and tidy, in line with the national policy of energy conservation and environmental protection, do not have to worry about environmental protection assessment.

Applications : 

1. UV curing screen printing polish

2. UV plastic glazing oil (hot stamping)

3. Optical disc protects UV varnish

4. UV curing adhesive

5.UV curing soft adhesive

6.UV marble coating

7. The UV shadowless glue

8. UV LED line light source in smart-phone

9. Microelectronic industry -UV photocurable

10. PCB industry UV LED photocuring

11. Medical device UVLED photocuring

12. Optical industry -ST-UVLED curing

13. UVLED curing application in optical communication industry

14. Scientific research and institution ST UV LED photocuring

Drawer Type UV LED Curing Oven UV Curing Machine For Timing Experiment

Drawer Type UV Light Curing Machine UV Curing Oven can be used for Timing Experimental UV Machine

Drawer Type UV LED Curing Oven UV Curing Machine UV Curing Oven can be used for Timing Experiment

Parameters :

Brand	DSX	Input Voltage	220V/110V
Name	Intelligent UV LED Curing Box	Intensity	Touch Screen Adjustable
Material of Light Head	Superconducting hot aluminum	Defensive Function	/
UV LED Chip	Korea LG UV LED Chip	Cooling Method	Air Cooling
Irradiance Area	200*200mm	Control Method	I/O
Irradiance Distance	5-20mm (best effect)	Add Coolant	/
Power of Light	400W	Environment	0-40°C
Wavelength	395nm (can be customized 365nm-420nm)	Quality Guarantee	One year

The above product parameters can be customized, welcome to consult online customer service.

Advantages : 

1.Energy saving : 80% less than mercury vapor lamps

2.Low temperature : cold light source, very low temperature rise, all materials can be perfectly solidified, no deformation of the sheet material, no need for secondary drying.

3.High efficiency : high light intensity, fast curing speed, ink does not stick to the board, good calendering effect.

4.Practical : industry standard equipment, easy and fast installation, power on and off, no preheating, simple operation, high efficiency.

5.Mercury vapor lamp will produce carbon monoxide harmful gas, and UV LED is a long wave, a single wavelength, will not produce gas, harmless to human body, the working environment is clean and tidy, in line with the national policy of energy conservation and environmental protection, do not have to worry about environmental protection assessment.

6.You can take the product to visit the spot test, the spot looks at the effect.

Applications : 

1. UV curing screen printing polish

2. UV plastic glazing oil (hot stamping)

3. Optical disc protects UV varnish

4. UV curing adhesive

5.UV curing soft adhesive

6.UV marble coating

7. The UV shadowless glue

8. UV LED line light source in smart-phone

9. Microelectronic industry -UV photocurable

10. PCB industry UV LED photocuring

11. Medical device UVLED photocuring

12. Optical industry -ST-UVLED curing

13. UVLED curing application in optical communication industry

14. Scientific research and institution ST UV LED photocuring