385nm UV Oven Closed UV Curing Box 3D Printing Curing

385nm UV Oven is for 3D printing curing. Closed UV Curing Box do not leak light and is used NICHIA light beads, imported UV LED Light Source.


Advantages of 385nm UV Curing Chamber :
Fast curing, good effect
No light leakage, no harm to the body

385nm UV Oven Parameters :

Model	DSX-UV-OVEN 204150	Manufacturer	Guangdong SpaceLight Technology Co., Ltd.
Dimensions	L300*W300*H2 3 5mm	Light output area	204 * 150 mm
Cooling	Air Cooling	Power Input	100-240V AC 50-60HZ
Power	420 W	wavelength	365nm-420nm optional
Drawer capacity	L244*W193*H67.5mm	Illuminance	> 500 mW / cm2   70mm at EIT Test
Material / Weight	White gold paint / About 15Kg White Sheet Metal	Display /Language	LCD Touch Screen
Function	Adjustable time, intensity, mode Time, intensity, mode adjustable	LED Cumulative Time	Record accumulated using time
RS232 Serial Communication	Can query and adjust intensity, time and mode	Control Method	Connected with MCU, PLC and other automatic equipment to control and feedback the work state

Application areas of UV Curing Chamber :
Microelectronics Industry - UV Light Curing Applications  
1 , mobile phone component assembly (camera lens, earpiece, microphone , housing , LCD module , touch screen coating, etc.)   
2 , hard disk head assembly (gold wire fixing , bearing , coil ,  die bonding, etc.)  
3 , DVD / digital camera (lens , lens bonding, circuit board reinforcement)
4 , motor and component assembly (wire , coil fixed, coil end fixed , PTC / NTC component bonding , protection transformer core)   
5 , semiconductor chip (moisture protection coating , wafer mask , wafer contamination inspection , UV tape exposure , wafer polishing inspection)   
6 , sensor production (gas sensors, photoelectric sensors, fiber optic sensors, photoelectric encoders, etc.)
7, 3D printing curing

PCB industry UV LED Exposure Box application
1 , components (capacitors , inductors , various plug-ins , screws , chips, etc.) fixed
2 , moisture-proof potting and core circuit, chip protection , antioxidant coating protection
3 , circuit board type (corner) coating
4 , ground wire , flying wire , coil fixed
5 , wave soldering through hole mask

Medical device UV Light Curing System application
UV glue bonding makes economical automated assembly of medical devices easier. Nowadays , the  advanced LED UV light source system , which can cure solvent-free UV glue for a few seconds , as well as the dispensing system , makes an effective and economical method for consistent and repetitive bonding of medical device assembly processes. The optimization and control of  UV light sources is very important for the manufacture of reliable medical devices. The use of UV-curable glue offers many advantages ,  such as lower energy requirements , saving cure time and location ,  increasing productivity and  making automation easier.  UV glue is commonly used to bond and seal medical devices that require very high quality and best reliability. UV glue curing Typical applications are in the medical device assembly , such as the need bond 1)  of different material ( or different mechanical properties ) 2)  material is not thick enough , can not use the soldering method  3 ) pre-production of sub-parts. .
1 , anesthesia mask    2 , syringe    3 , catheter    4 , intravenous infusion tube    5 , vascular implant accessories 6 . Endoscope    7 , arterial positioning    8 , tubular drainage device    9 , tracheal tube    10 , blood oxygenator    11 , hearing aid    12 , detection , monitoring , and imaging equipment    13 , biochip    14 , bonding PVC, thermoplastic ( polycarbonate) Fat and ABS) 

Optical Industry - ST-UVLED Light Curing Applications  
1 . Optical component assembly (lens group , prism , optical engine assembly)     
2 . Image instrument assembly (microscope , endoscope , infrared , night vision , probe, etc.)
 Optical communication industry UVLED light curing application  
1 . Passive components (wavelength division multiplexer WDM, array grating waveguide AWG, optical splitter SPLITTER, optical isolator ISOLATOR, optical coupler COUPLOR, etc.) , various glass package structure bonding or potting , fixing of small components Wait.  
2 . Active devices (coaxial devices TOSA/ROSA/BOSA, VCSEL , laser collimators, etc.), especially FTTX low-cost miniaturized plastic package structures  
3 . Fiber optic cable (overcoat , marking , bonding, fiber optic gyroscope)

Research and Institute - ST-UVLED Light Curing Application
1. Polymer chemistry ( nano coating , photocurable resin , photosensitizer , monomer , UV ink, etc. )
2 , medical polymer materials ( medical plastics , catheters ), microorganisms
3 , photochemistry  ( photocatalysis , photoexcitation , photosynthesis, etc. )
4 , semiconductor  ( light accelerated etching , cutting , uv tape, etc. )

Other Apps
1 , ultraviolet analyzer, biological genetic engineering, molecular genetics, medical health, biological products, drug research, health and epidemic prevention, dye chemical, petrochemical, textile industry, ** political and legal departments, cultural relics and archaeological departments, where the need for fluorescence analysis The department can be used.  
2 , biochemistry  ,  microbiology ,  genetics ,  genetics ,  medicine  ,  catalysis, each channel uses different wavelengths of ultraviolet LED , from 240nm to  410nm , every 5nm step, for detailed analysis    
3 , ultraviolet light therapy, medical applications, such as: dental curing, vitiligo treatment, wound complex promotion.  
4 , standard light source, because LED light spectrum is relatively single, energy is consistent, can be used as an effective standard light source  
5 , criminal investigation light source, with high-power LED , can emit a uniform intensity of light from365nm to 780nm , from ultraviolet, purple, blue, green, blue, yellow, orange, red, to the infrared band, can provide 12 bands The light and includes a white light.  

FPC surface protection adhesive curing features: 
1 : Cold light source, no heat radiation, especially suitable for liquid crystal edge sealing, film printing requires a small temperature rise area for use. 
2 : Instantly illuminate, instantly achieve 100% power UV output, and the irradiation intensity can reach8000-9000mW/cm2. 
3 : Small size - makes the equipment easy to integrate into fully automatic production lines and equipment.
4 : It does not use toxic substances and does not produce ozone. It is a safer and more environmentally friendly alternative to traditional light sources.

How to Correctly Choose UV Light Source

There are many specifications for UV Curing Equipment. How can I know which UV Light Source UV Curing Equipment I need ? How to select the suitable UV LED Spot Light Source? Linear UV Light Source? Large Area UV LED Light Source? What applications are they suitable for?

After UV LED Spot Light Source, linear UV LED curing machine emerges in IT electronics industry. This paper introduces the principle, structure, characteristics and application of Linear UV LED Light Source. Linear UV LED light source is different from the scattered light emitted by mercury lamp. The ultraviolet light emitted by UV LED linear light source is a narrow linear light nearly parallel to the light, with high energy concentration, irradiation intensity and curing efficiency. It is to avoid UV damage outside the work area and can also form a curvilinear light source. It is used in LCD panel, touch screen and printing.


1.Introduction of UV Curing
In the special formulation of resin to add photo-initiator, absorption of UV Curing Equipment in the high intensity of UV light, the generation of active free radicals or ion group, which triggered polymerization, cross-linking and grafting reaction, so that the resin (UV coating, ink, adhesive, etc.) in a few seconds (ranging from liquid to solid). This process is called “UV Curing”. UV curing is widely used in adhesive, paints, inks, coatings and other fields.

100*100mm High Power Surface UV Curing Machine

2.The characteristics of UV LED
The UV LED (UV light emitting diode) is a solid-state semiconductor device that can directly convert electrical energy into ultraviolet light. UV LED spot light source working temperature under 100℃, and usually has a long service life, high reliability, high luminous efficiency, less power consumption, no radiation, beneficial to environmental protection and other features. In recent years, it have been applied gradually in the UV curing.

- Long service life : over 20,000 hours
- Energy saving effect is significant, up to 90%
- No infrared radiation : will not cause thermal stress and thermal deformation of the work-piece
- Compact size, flexible configuration : volume is only 0.1cm3
- Energy concentration : more than 98% of the light output is in the ultraviolet band
- The main peak is narrow and single : over 90% of the light output is concentrated in the range of 10nm near the main wave peak
- Dc low voltage drive : suitable for portable UV equipment
- The output power is stable and continuously adjustable
- Flash : no preheating time is required, and the response time is in microseconds
- The opening and closing times do not affect the service life. No shutter is required
- Environmental protection : RoHS compliant, mercury free


3.Situation of UV Curing Equipment Application
UV curing equipment and mercury lamp can provide the same UV light, but also has a long life, no heat radiation, low consumption, low cost, accurate and adjustable power, small size, light source shape can be customized, mercury lamp does not have the characteristics. It has been successfully applied in many fields of industrial assembly : LCD manufacturing, camera and other optical products manufacturing, optical disc manufacturing, watch manufacturing, buzzer, mobile phone keypad assembly, electronic circuit board manufacturing, polarizing parts manufacturing, micro-motor assembly and other electronic parts manufacturing.

The application of UV curing equipment for civil use is also gradually developing :
In the field of daily necessities, it is mainly used in production of household goods, furniture and toys. The the field of glass technology, the assembly of glass crafts. Jewelry and other accessories of the assembly, Mosaic, positioning and printing areas.


4.Structure and Features of Linear UV Curing Light Source
UV LED has many advantages, but there are still many restrictions on the popularity of UV LED. The current linear UV LED light source has high cost, small single power, complex optical path system, narrow crest and poor matching of photo-initiator and other problems.

The first application to gain acceptance and popularity is UV LED Spot Light Source :
The size of UV LED light emitting unit is only a few millimeters, and the luminous body is mostly a cube with a side length of 1mm, with small luminous point, which is very suitable for achieving good focusing effect through the optical path system and realizing small light spot and high intensity ultraviolet irradiation.
UV Spot Light Source is suitable for curing only a few millimeters of area, but also requires high intensity of ultraviolet radiation spot curing occasions, such as : laser head, optical fiber connector, optical fiber coupler, LCD, OLED, hard disk, smart card, sensor, micro motor, encoder manufacturing, solder joint reinforcement, etc.

1+4 Portable UV Spot Light Source

5.The application of linear UV curing Light Source
Linear UV Light Source is mostly narrow and slender linear light. It is necessary to design special optical path system to converge multiple light spots emitted by a row of UV LED into narrow, uniform and high intensity linear light.

At present, there are several types of linear UV light sources :
(1)This kind of line UV light source is suitable for the long and thin work-piece to carry on the solidification irradiation occasion. The energy is high, the solidification efficiency is high. But on the other hand, the working distance is sensitive, has the strict request to the irradiation distance, generally only has several millimeters to ten millimeters working distance.
(2)This kind of line illuminant illuminate is even, not sensitive to working distance, general radial width is controlled in millimeter, but energy is a bit weak.
(3)The irradiation range of this kind of linear UV light source is large and working distance is not sensitive, but compared with the first two kinds, the irradiation intensity is the weakest.
(4)The curvilinear UV light source is composed of several linear UV light source, which can form a special shape and meet the needs of special stations.

Cost and luminous intensity are the main constrains to the popularity and application of UV LED. The development and design ideas of line UV light source should follow the following points :
Optical path system is the key. A good optical path system should be concentrated and uniform energy, so as to reduce the deformation of the solidified work-piece and reduce the solidification stress, improve the solidification accuracy. High irradiation intensity makes curing more efficient. Special shape linear UV light source, more adaptability, meet station needs, make its application more popular. More energy saving and environmental protection and lower cost.

(1)Linear UV light source and dispensing machine cooperate to realize rapid sealing and streamline operation of the chip. Due to high energy of UV LED, stable light output and even irradiation, the production is more efficient.
(2)Since UV LED is a cold light source without thermal radiation and with small temperature rise, it can meet the requirement of LCD production. In the manufacturing process of LCD, the UV LED Line Light Source is used to seal the edge of LCD, and the connection between FPC and LCD is reinforced with cables, which is simple, fast and efficient.
(3)Linear UV curing light source with UV ink can be used in the printing field.
(4)Manufacture of syringes and needles.
(5)Headphones, mike manufacturing.
(6)Sensor encapsulation.


6.Large Area UV Curing Light Source
UV LED surface light source also has no thermal radiation, and the temperature in the curing furnace can be controlled at room temperature, many LED luminous points are evenly distributed, and many groups of professional lens optimized for UV irradiation have good irradiation uniformity and excellent uniformity of irradiation intensity between edge and center. The shape and size of the luminescent area can be customized according to user requirement.
Large area UV curing light source in the same input power, compared with mercury lamps, irradiation cost is more expensive. In the terms of output power, the cost is more expensive than mercury lamps.
At present, the main breakthrough of UV LED surface light source application and popularization is small surface light source. Now, the irradiation intensity of small surface light source can reach more than a few hundred to a thousand milliwaittts per square centimeter. High irradiation intensity brings higher production efficiency. On the other hand, small surface light source energy concentration and no heat radiation, so its cooling system and the entire irradiation system tend to miniaturization, more convenient application.
Compared with UV spot light source and linear UV light source, the cost of UV surface light source is high, which restricts the application and development of surface UV curing light source.


7.Brief Summary
With the continuous reduction of UV LED cost, the popularity of UV LED is transiting from UV spot light source to line UV curing light source (it will take some time for the popularity of surface UV light source). In the field of industrial assembly and daily necessities, line UV light source will get more attention.
At the same time, with the adaptive development of UV LED photo-initiator, the application of UV LED will be more extensive and its advantages will be more and more obvious.

UVC Underwater Detection Sterilization Lamp UV Intensity Meter

Water treatment is divided into waste-water treatment, urban water supply treatment, drinking water treatment, pure water treatment, aquaculture water treatment;There are two methods of water treatment, the first is to put the UVC Sterilization Lamp in the water sterilization, the second is to put the sterilization lamp in the casing, because the flow rate of water is too fast, sterilization lamp time sometimes less than 1 second, so will require the use of high power sterilization lamp or choose a longer UV lamp to sterilization.





UV Intensity Sensor UVC-WP probe is one of the 9 probes of LS125 ultraviolet irradiance meter. It is a probe specially developed for water treatment high-power sterilization lamp. The response wavelength of the probe is 230nm-280nm, with waterproof function, waterproof depth up to 1 meter, and can detect the intensity and energy of the sterilization lamp.

Parameter of UVC UV Measurement:
1.Spectral Response : 230nm-280nm, λp=254nm
2.Power Measurement Range : 0-200000μW/cm2
3.Power Resolution : 0.1μW/cm2
4.Energy Measurement Range :  0 - 9999999μJ/cm2
5.Write Time : 0 - 99999S
6.Measurement Accuracy :  ±10 %
7.Sampling Rate : 6 times / s
8.Units :  μW/cm2 (default)，mW/cm2，W/m2
9.Test the Diameter of Light Hole : ￠10mm
10.Probe Size : diameter 50mm * thickness 20mm
11.The Depth of Waterproof : 1m



Advantages of UV Intensity Meter Caliibration :
1. Large range UV Intensity Meter Caliibration, the maximum power can be measured to 200000 W/cm2.
2. The instrument can measure the energy value and power value at the same time.
3. It has rich statistical functions, such as real time value, maximum value, minimum value, average value, measurement duration and energy value.
4. Can switch 3 measurement units, respectively W/cm2, mW/cm2, W/m2 data conversion between different units without manual calculation.
5. With waterproof function, waterproof depth up to 1 m.

How to Embody the Utility of UV LED Photo-Curing Equipment ?

UV LED Curing Accessories uses UV LED chip as the light source, and various control modes are controlled by the controller. The electrical signal is converted into optical signal, and a single ultraviolet wavelength with high energy and purity is emitted.

UV curing accessories is ready to use, instantly lit, without preheating. According to DUIY=1/5 (preparation time=1/5 exposure time), the service life of UV LED curing device is 30-40 times as long as that of traditional UV mercury lamp. UV LED curing device reduces the time to change the bulb, improves the production efficiency and reduces the input of production cost. While the traditional UV mercury lamp in the work, mercury lamp start slowly, need to warm up for a period of time before work, and open and close affect the life of the lamp, must be lit all the time. It not only causes unnecessary electricity consumption but also shortens the working life of mercury lamps.



Traditional UV mercury lamp curing agent uses mercury lamp illumination. UV mercury lamp contains mercury, waste disposal, transportation is very troublesome, improper treatment will produce serious pollution to the environment. UV LED Curing Device uses UV LED chip as the light source, without pollution to the environment.therefore, the use of UV LED curing device is more environmentally friendly.

UV curing machine adopts high power LED chip and special optical design, UV light to achieve high precision, high intensity irradiation. The radiation intensity of UV Light reached 8600mW/cm2. With the latest optical technology and manufacturing technology, the high-intensity output and uniformity are more optimized than the traditional mercury lamp irradiation mode, which is almost twice the intensity of the traditional mercury lamp irradiation mode, so that the UV adhesive curing fast, shorten the production time, greatly improve the production efficiency.

When the traditional spot light curing machine used for mercury lamp increased the irradiation channel, the increase of the channel will result in the decrease of the output energy of single irradiation channel. In the UV curing equipment, each head glows independently, and the irradiation energy is not affected by the increase of channels, and always remains at the maximum value.

At the same time, whether the effective mode of mercury lamp irradiation, mercury lamp needs continuous lighting work, the power has been in a state of consumption. The UV curing accessories only consumes power when irradiated, while the power consumption is almost zero when standby. Let’s do a simple calculation : the energy saved by the curing agent per spot light source : 270W*8H*365days=800KW/H

It can be seen that each unit can save only 1000 yuan in annual electricity consumption. Not only that, by saving electricity, each car can indirectly reduce its annual carbon dioxide emissions by 1.4 tons, equivalent to the annual exhaust volume of a car.

Compared UV Mercury Lamp with UV LED
Type	UV Mercury Lamp	UV LED Light
Length	800-1000mm（adjustable）	800-1200mm（adjustable）
Emission spectrum	broad：205~445nm	focus：395nm
Applicability	Not applicable to thermal sensitive materials	Almost all materials
Life	≤1000 hours	≥20000 hours
Optical output attenuation	Attenuation serious	Almost no attenuation
Ozone generating	Yes	No
Thermal effect of light source	High heat	Low
Start	Slow start, off after the need for complete cooling before starting	Can be started instantaneously
Cooling	Air or water	Air or water
The volume of light source（L*H*W）	Large in size（3m*1.2m*1.2m）	Small size（1m*0.2m*0.2m）
Light source device	Transformers, lamps, capacitors, fans	Light source module, cooling system
Equipment maintenance	More difficult to clean	Easy to clean
Electric power	Lamp power：8KW*3=24kw Motor power：4KW Ordinary type：10-15KW Large models：20-36KW	LED power：2KW Cooling motor power：2KW Total power：4KW
Daily electricity （1.2元/度，每天工作10小时）	28*10*1.2=336元/天	4*10*1.2=48元/天
Average annual electricity bill（每年工作300天计算）	336*300=100800元/年	48*300=14400元/年
Annual cost of lamp replacement （life of mercury lamp is 1000 hours，unite price is 400元/支）	300*10÷1000*400*3=3600元/年	LED annual depreciation expense （six years for calculation） 50000÷6=83333元/年
Annual savings（electricity + lamp charge）	（100800+3600）-（14400+8333）=81667元/年
One life cycle cost savings	81667*6年=490002元

Seeing that UV LED curing equipment can save so much, do you also need to consider updating your equipment ?

Guangdong SpaceLight Technology Co., Ltd. is special in research & development, production and sales : UV LED exposure machine, professional UV Light Source. Our products, through using Japan NICHIA UV LED, Korea SVC UV LED, LG UV LED, etc., super power integration, low voltage and high current voltage decision scheme, and with the patented optical distribution system, ensure the stability of the light source system and the uniformity of the light source.

Note : our company can customize the light source and upgrade the traditional light source.

Welcome to inquiry : 1651063690jennifer@gmail.com (Jennifer)

20W NICHIA NVSU333A 365nm UV Flashlight UV Torch

Highest 365nm Handheld UV Torch, strongest in the world. It can shoot at a distance of up to 10 meters.


About NICHIA 365nm UV Torch :
The light outlet should not be placed vertically on the table after starting up. In this case, the heat will not escape and the lamp beads will burn off.
UV LED is harmful to human eyes. Do not look directly at it.
Do not block the light outlet after starting up, the temperature is very high.








Parameter of High Power NICHIA LED UV Torch:
1.Part of UV LED





2.Part of UV Flashlight
Length : 247mm
Diameter of head : 65mm
Diameter of the tube body : 35mm
Net Weight : 432g, excluding battery
Flashlight *1, hand rope *1, aluminum box *1, black filter added at the light outlet *1
Battery：two 26650battery


 
 
Application of Handheld NVSU333A 365nm UV Blacklight:
1.Fluorescence observation of ore;
2.Oil cleaning and testing;
3.Biological polymerization and fluorescence observation;
4.Air conditioning refrigerant leakage detection;
5.All kinds of trace crack detection;
6.Engine oil leakage detection;
7.UV glue table for curing, curing without shadow;
8.Collection of notes, amber, jade, security detection;
9. Criminal investigation: handprint, fine spot, blood stain observation, biochemical test;
10. Penetration detection, fluorescence detection, cosmetics whitening agent, fluorescence agent detection;
11. Confirmation of degreasing cleaning: confirmation of degreasing cleaning for food industry, kitchen, cooker and tableware;
12. Pollution inspection: electronic components, motherboard, dust inspection, LCD panel, clean room access inspection;
13. Fluorescence inspection: fluorescence penetrant inspection of steel, non-ferrous metal, automobile, aircraft, etc., fluorescence magnetic powder inspection;
14. Leakage inspection: oil pressure machine, tank, drain pipe, etc., leakage inspection using fluorescein, pipeline leakage, chemical glue.

Here's how the raw amber reacted under fluorescence:




Of cause, all the UV Flashlight, 333A is the most effective!

Contact Us:
Company : Guangdong SpaceLight Technology Co., Ltd.
M.P: +86 18924372460 
Skype:Jennifer Jian
E-mail:1651063690Jennifer@gmail.com
WhatsApp : +86-18924372460

365nm NVSU333A Highest Power UV LED Spot Light Source

This 333A NICHIA UV LED point light source is equipped with the world-recognized top-quality power UV Spot Curing Light, Japan Nichia NICHIA single core 365nm, 20W electric power. Very penetrating power, can instantly cure UV glue lamp adhesive. It has excellent effects in the fields of fluorescence detection, magnetic particle inspection, and fluorescence excitation.
 
The DSX333A-II UV Light adds two new features to its predecessor.Added time relay and foot pedal control. Convenient for automated operation of the assembly line. If you need to customize other features, please contact us directly. 

Parameters of 333A UV Spot Light Source:
Brand :SpaceLight
Type：DSX333A
Wavelength：365nm
Illuminance：>10W/cm2
Power Adapter：AC  0-250V
Plug Interface : British standard adapter
Size of host：L170mm W130mm H75mm
Weight：about 1.05kg （including irradiation head, power supply cable）






Parameters of irradiation head :
Cooling method : air cooling
Cable Length ：1.5-2M


Lens : standard with a lens: round spot lens (φ1.5mm，φ3mm，φ4mm，φ5mm，φ6mm，φ8mm，φ10mm，φ12mm，φ15m,φ20mm..), or rectangular lens (3*12mm, 4*16mm, 5*20mm)


Standard Equipment : controller*1, irradiation head *1, foot pedal*1, power cord*1


Option : UV Protective glasses, UV protective clothing, or UV protective mask

Single UV Light Beads please contact us. (review here)

For more UV LED Point Light Source Please click here : Spot Curing UV Light Sources






A、Foot Pedal        B、Irradiation Head        C、Timer    D、Reset Switch      E、 Power switch


The main application of UV-LED Spot Light Source:
1. Hard disk head assembly (head package, gold wire fixing, bearing, coil, chip bonding, etc.)
2. Motor and component assembly (wires, coils, fixed coil ends, PTC/NTC components, protection of transformer cores)
3.DVD/ digital camera (lens, lens paste, circuit board reinforcement)
4. Sensor production (gas sensor, photoelectric sensor, fiber optic sensor, photoelectric encoder, etc.)
5. Mobile phone component assembly (camera lens, handset, microphone, housing, LCD module, touch screen coating, etc.)
6.TFT-LCD liquid crystal panel port
7.TFT - Paste Package of LCD Liquid Crystal Board FPC
8. PCB industry UV LED light curing applications.
9. Optical Industry - ST-LED UV Curing Applications
10. Optical Assembly (Lens Group, Prism, DLP Optical Engine Assembly, CCD, COMS )
11. Optical Communication Industry LED UV Curing Applications
12. Optical communication industry components ( PLC splitter, wavelength division multiplexer WDM , array grating waveguide AWG, etc., bonding or encapsulation of various glass packaging structures, fixing of tiny components, etc.)
13. Research and Institute - ST-UV LED Light Curing Applications
14. Medical Devices and Medical Accessories LED UV Light Sources Curing Applications
15. capacitive touch screen fit curing
16. Laser UV curing application

Contact :
E-mail : 1651063690jennifer@gmail.com
QQ : 1651063690
Phone : +86-18924372460  Jennifer

LG UVC LED UV Disinfection Lamp LEUVA66G00HF00 10mW 278nm Original Direct Supply

LG UVC LED UV Disinfection Light LEUVA66G00HF00 10mW 278nm Original Direct Supply

High Power UVC LED 275nm-278nm-280nm, LG Original Shipment, Deep UV 10mW, High Power Model: LEUVA66G00HF00, Size 6060, Quartz Glass, in Stock, Original Factory Direct Sale

Dedicated UV lamp beads for sterilization, ozone detection, surface or water contamination, protein analysis, DNA identification, drug development, optical sensing, image tonal measurement, fluorescence excitation, etc.





Parameters of LG UVC Light LEUVA66G00HF00 :








What Features do UVC Have ?
1. Compact, Slim Size, Light-weight SMD Package
2. Low Power Consumption
3. Robust Deep UV Light Source
4. Low Thermal Resistance
5. High Quality and High Reliability

How to Classify the Wavelength of UV LED?
UV LED can be classified by spectrum in a number of ways. Among them, the ISO classification standard for sunlight ISD-DIS-21348 classification can be divided into UVA（400-315nm），NUV（400-300nm），UVB（315-280nm），MUV（300-200nm），UVC（280-100nm）.

How to Distinguish UV?			The Applications of UV :
Near UV	UV-A	315-400	Hardening of polymer or printer inks, measurement of gas, measurement of nitrogen elements, insect traps, lighting, optical induction, image tone measurement ID, identification of banknotes, etc.
	UV-B	280-315	UV hardening, optical therapy, optical induction, image tone measurement, crime analysis, protein analysis, DNA identification, drug development, etc.
Deep UV	UV-C	100-280	Sterilization, ozone defection, removal of surface r water pollution, protein analysis, DNA identification, drug development, optical sensing, image tone measurement, etc.

Other Sizes of UVC, Please contact : 1651063690Jennifer@gmail.com