15W Korea LG Four LED Chips UV Flashlight UV LED Light Beads 365nm

Korea LG Four Chips 365nm UV LED Light Beads is encapsulated quartz glass lens. In the encapsulation technology, the lamp bead encapsulated with four chips is not suitable for silicone lens, which is easy to be yellow and fall off, and the light fades quickly.

LG UV LED Curing LED Chip, Newly developed ultra-high quartz glass lens + ceramic packaging technology, small angle light design, packaging size of 7070, silicon-based UV LED emitting high purity purple light, high current resistance, low thermal resistance, etc.

Suitable for : electronic offset printing (adhesive curing), ceramic and metal painting glazing, fiber drawing, printing, ink printing and other curing application market.

Product Feature :

Ceramic substrate seal

ESD protective

Support Surface Mount Technology (SMT)

Size : 7.0*7.0 mm

Typical Optical Power :

385nm  4200mW @1500mA 

395nm  4400mW @1500mA 

( Maximum allowable working current : IF max= ：2000mA )

Chip type : 55 mil silicon vertical LED chip

Send light angle : 68°

Application :

banknote inspection, mosquito control, manicure, industrial curing

Characteristic Parameters : (T solder pad = 25 ℃)

Characteristic	Symbol	Minimum Value	Typical Value	Maximum Value	Unit	Test Condition
Optical Power (385)	∮e	4000	4200	5000	mW	IF=1500mA & 25 ℃
Optical Power (395)	∮e	4000	4400	5000	mW
Forward Voltage	VF	3	-	3.8	V
Direct Current	IF	-	1500	2000	mA
Backward Voltage	VR			5	V
Wavelength	WLR	365		405	nm
Irradiation Angle	2θ1/2	-	68	-	°
Thermal Resistance			2.5		℃ / W
HBM	ESD		8000		V
T j (Junction Temperature)	T j			125	℃

Note :

1.When the lamp bead is normally lit, the maximum allowable current is IFMAX = 200mA

2.The lamp bead test data is obtained by UV integrating ball test in cold pulse mode.

3.For lamp bead module products, the maximum temperature TC of PCB board shall not exceed 90℃. (protect chip junction temperature T j≤125℃)

4.The recommended current of this product is IF=500mA, mainly used for curing class light mode for customers.

Optical Power Parameter : (T solder pad = 25 ℃)

Wavelength	Wavelength Range		Optical Power		Test Condition
	Minimum	Maximum	Grading	Optical Power mW
UV Wavelength	380	405	KM	4000-5000	IF=1500Ma & 25 ℃

Note : optical power test error : ±8%

Product coding rules :

VG-P5-KM-TD

Example : the rank of peak wavelength is P5. It means that the peak wavelength range is 380-385nm.

Voltage Step :

Rank	Minimum	Maximum	Test Condition
TD	6.5	7.5	T solder pad = 25 ℃

Step Size :

1. Peak wavelength grading

Rank	Minimum	Maximum	Test Condition
P1	400	405	T solder pad = 25 ℃ IF = 1000mA
P2	395	400
P3	390	395
P4	385	390
P5	380	385

Note : peak wavelength test error : ±1.5nm.

2. Optical Power Grading

Rank	Minimum	Maximum	Test Condition
KM	4000	5000	T solder pad = 25 ℃ IF = 1000mA

Note : Luminance test error : ±8%.

Precautions for use

How to store Korea LG UV LED ?

1. The product should be stored in an environment with a dry, relative humidity of less than 30% and a storage temperature of 5 to 30 °C. 

2. Avoid external damage to the vacuum bag to prevent the bag from leaking and getting wet. 

3. Pay attention to moisture. If it is damp, put the patch reel in a 60 °C oven for 24 hours; remove the tape from the bag, preferably within 12 hours 

4. LED lights that have been unsealed from the original packaging but have not been soldered should be stored in one of the following ways: 

a. After opening, the LED lights can be resealed in the original vacuum bag. 

b. Store the parts in a sturdy metal container with a tight lid attached. Place the fresh desiccant and humidity card in a container and check that the relative  humidity is less than 30%. 

c. Store the parts in a dry, nitrogen-purified cabinet or container and require the cabinet or container to effectively maintain the relative humidity below 30%. 

d. After reopening, the reflow soldering is completed within 24 hours. The workshop condition is ≤30°C/60%RH. 

e. If there is no environment with a relative humidity below 30% for storage, one hour before reflow, it must be baked. 

5. When stacking PCBs or components that contain LEDs, do not drop all weight on the lens. The force applied to the lens can cause the lens to fall off. 

A clearance of at least 2 cm should be left above the LED lens, and the foamed wrapping paper should not be used directly on the lamp. The force from the foamed packaging can damage the LED 

reflow soldering conditions 

1. The printed circuit board should be prepared or cleaned in accordance with the manufacturer's specifications before the LEDs can be placed or soldered onto the PCB. 

2. Our company's LEDs are designed to be soldered to the PCB by reflow soldering. Reflow soldering can be done in a reflow oven or by placing the PCB on a hot plate and 

following the reflow profile.

3. Pay attention to the reflow conditions when using, and reflow soldering after debugging the reflow temperature. Reflow conditions: preheating temperature 100 ~ 150 ℃; reflow 

soldering temperature of 230 ~ 260 ℃, the welding time of 10 seconds.Operators should take electrostatic protection measures and all equipment must be grounded reliably. 

4. Reflow soldering should not exceed 2 times at most. 

5. Do not apply pressure to the lamp bead when passing the lamp. 

6. After the lamp is over, the PCB board cannot be packaged immediately. The PCB board and the lamp bead should be naturally cooled. 

Cleaning 

after reflow soldering 1. After soldering, the lamp bead should be cooled to room temperature for further processing. Premature handling of the device, especially around the lens, can result in product damage. 

2. It is recommended to check the weld consistency. After avoiding the selected parts of the board, the welding process should be able to achieve complete look at reflux (no clear 

significant weld particles). From the back of the package and board, there should be almost no holes visible in the soldered area. 

3. When cleaning the PCB after soldering, use isopropyl alcohol to clean the PCB. Do not use ultrasonic cleaning. Do not use water to clean PCB boards that have been fitted with lamp beads. 

4. Do not use the following chemicals for cleaning: chemicals that 

may cause outgassing of aromatic hydrocarbon compounds (eg toluene, xylene) 

a. methyl acetate or ethyl acetate (ie: nail polish cleaner) 

b. cyanoacrylate Ester (ie: 

superglue ) c. Ethylene glycol (including Radio Shack® precision electronic cleaner) 

d.PLIOBOND® adhesive      

Installation method 

1. High Intensity UV LED Chip has anti-static requirements, and appropriate anti-static measures should be taken during installation and use.  

2. Pay attention to the arrangement of the external lines of various devices to prevent the polarity from being wrong. The device must not be too close to the heating element and the operating conditions should not exceed the specified limits. 

3. When deciding to install in the hole, calculate the hole size and tolerance of the hole on the board to avoid excessive pressure on the board. 

4. Avoid subjecting the LED to any vibration and external forces. 

Operating conditions 

1. In order for the LED to operate under stable conditions, a series of protective resistors must be connected in series, and the resistance value can be measured by the supply voltage or current of the LED. LED work 

for the voltage and current given by a variety of product specifications requirements LED. 

2. The circuit must be designed to prevent overvoltage (or overcurrent) that can occur during LED switching. Short current or pulse current can damage the LED connections. 

3. When the Fiber Drawing UV Curing UV Light LED light source is working, the ambient temperature will affect its life reliability. Please keep away from the heat source while working, and the surface temperature should be controlled within 60 °C 

. 4. Incompatible volatile organic compounds in the LED-based solid-state lighting design. , may weaken the performance of the illumination system, shorten its 

life, so avoid the use of organic compounds in the design and operation. 

Other matters 

1. This product is a silicone package and cannot be extruded with a hard object. 

2. All equipment that touches the LED must be grounded. Operators must wear grounded anti-static gloves, anti-static shoes and anti-static clothing.